Buying guide · Updated 6 November 2026
The correct replacement crankshaft must match your engine’s dimensions and operating hardware, as well as its part reference. Cylinder count, engine capacity and a similar photograph are not enough to confirm a match.
Use this guide with your mechanic or engine builder before you shop replacement crankshafts. It focuses on a replacement for the existing engine specification. A stroker or performance conversion requires a separate build plan.
1. Start with the engine code and reference number
Gather the VIN, build date and code from the engine actually installed. Note whether it is petrol or diesel and the relevant engine variant. If the vehicle has had an engine swap, tell the supplier before using the original VIN as a reference.
Record the original crankshaft’s service number where known, and photograph its markings. Keep suffix letters and digits. If your reference has been replaced by a later number, ask for confirmation of that supersession and the applicable engine version.
A listing under a broad family such as 4D56 does not make every 4D56 crankshaft interchangeable. Our catalogue separates 4D56-CRDI reference 1100A135 and 4D56-T reference MD376960. Confirm the exact application before choosing either.
2. Check dimensions and bearing compatibility
| Feature | What your engine builder should confirm |
|---|---|
| Stroke | The specified stroke for the intended engine configuration. |
| Main and connecting-rod journals | Diameters, widths and condition; the correct matching bearing specification. |
| Thrust arrangement | Thrust-bearing location and the required axial clearance. |
| Journal fillets and oil passages | Compatibility with the bearing design and lubrication requirements. |
| Overall configuration | Length, counterweights and clearance to the engine assembly. |
Do not order a bearing set solely because the previous engine used that size. A previously reground crankshaft may require a different bearing specification from a new replacement. Confirm the new shaft’s supplied journal size and the measured assembled clearance.
MAHLE explains that bearing clearance depends on the application and operating conditions, and that manufacturing tolerances affect the final assembled clearance. The engine builder should measure the actual components and follow the relevant specifications. MAHLE bearing-clearance guidance.
3. Compare the drive, flange and sensor arrangement
Have the workshop compare the front snout, keyway or gear mounting, pulley and oil-pump drive arrangement where relevant. At the rear, verify the flywheel or flexplate mounting and seal arrangement. Check the crankshaft position trigger or reluctor configuration and whether it is included or transferred.
These details are particularly important when two shafts share a broad engine-family description. Photos of both ends, the full shaft and any trigger components are more useful than a single side view.
4. Choose the specified material and supplied components
Some listings offer cast iron and forged steel variants. Select the material agreed with your engine builder, then confirm it on the quote and order. Material is a separate check from fitment: a forged shaft with the wrong dimensions is still the wrong part. Read our cast iron versus forged steel crankshaft guide for the questions to ask.
Also establish whether bearings, gears, plugs, a trigger wheel or other accessories are included. A crankshaft-only price should not be compared with a kit price without allowing for the difference in contents.
Before you place the order
- Full engine code and installed-engine details
- Original part reference and any supersession
- Required stroke and journal specification
- Front drive and rear flange photographs
- Sensor trigger and material requirements
- Written list of supplied components
The builder should also identify why the original crankshaft or bearings failed and the associated repair work required. Retain the packaging, check the supplied reference and have the new shaft inspected before machining or installation.
Crankshaft buying questions
Will any four-cylinder crankshaft fit a four-cylinder engine?
No. Stroke, journal dimensions, drive features, mounting and other details vary between engines. Cylinder count only describes the broad layout.
Can I reuse my old bearings with a new crankshaft?
Do not assume so. The builder must specify suitable bearings and check the actual assembled clearance and condition.
Does a forged option automatically fit where the cast option fits?
Confirm the exact catalogue reference and dimensions for both options. The material description by itself is not fitment evidence.
Related buying guides
- How to Choose the Correct Camshaft: Engine Codes, Part Numbers and Position
- Camshaft Replacement Cost in Australia: Parts, Labour and What to Budget For
- Cast Iron vs Forged Steel Crankshafts: Which Replacement Should You Choose?
Find the right part for your engine
Have your VIN, engine code, original reference and photos ready. We can help you check the correct listing before you order.
